The project aims at designing Home automation system using Wi-Fi technology,you can start with one room or automate the entire house.The system offers one-touch control of lights and appliances.
FEATURES:
Design based on highly proven IC ULN2003 as driver.
High Current (7A) Capability for each relays.
Simultaneous 2 load control with 0-100% MAX 8A dimming.
Act as 2 channel solid state relay with ON/OFF and dimming.
Snubber circuit enable.
Accurate firing angle control and smooth dimming.
0-100% dimming.
WiFi Enabled.
Inbuilt power supply.
Measure the energy consumption of the respective switchboard.
Dimension: 62X182 mm.
High quality PCB FR4 Grade with FPT Certified.
ESP-12 Features:
SDIO 2.0, SPI, UART
32-pin QFN package
Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
Integrated RISC processor, on-chip memory and external memory interfaces
Integrated MAC/baseband processors
Quality of Service management
I2S interface for high fidelity audio applications
On-chip low-dropout linear regulators for all internal supplies
OVERVIEW: 8051 are popular with both industrial developers and hobbyists alike due to their low cost, wide availability, large user base, extensive collection of application notes, availability of low cost or free development tools, and serial programming (and re-programming with flash memory) capability. They are also commonly used in educational programming.
FEATURES:
High quality Atmel micro-controller development board.
The DIP40 locking device, easy to remove the ATMEL micro-controller for reuse.
8 independent LED.
1 * 4 independent keys.
4* 4 keypad matrix.
RTC DS1307 with battery connector
AT24C02 I2C external memory.
I2C EEPROM Interfaces
The MAX232 chip RS232 communication.
16X2 LCD interface (character display).
All IO ports pin have extraction and clearly marked.
OVERVIEW: PICs are popular with both industrial developers and hobbyists alike due to their low cost, wide availability, large user base, extensive collection of application notes, availability of low cost or free development tools. They are also commonly used in educational programming.
Features:
High quality PIC microcontroller development board.
The DIP40 locking device, easy to remove the PIC microcontroller for reuse.
8 independent LED.
1 * 4 independent keys.
4* 4 keypad matrix.
RTC DS1307 with battery connector
AT24C02 I2C external memory.
I2C EEPROM Interfaces
The MAX232 chip RS232 communication.
3 ADC potentiometer input conversion.
16X2 LCD interface (character display).
All IO ports pin have extraction and clearly marked.
On Board Power supply 3.3V,5V 12V,GND.
8 pin DIP switches.
3 ADC potentiometers.
RS232 Connector.
On board ICD ICSP Programmer pinout for PICKIT2 and PICKIT3.
The board also has inbuilt Xbee footprint.
Stackable Arduino shields.
Raspberry Pi expansion connectors.
ON/OFF slide switch.
I2C bus.
SPI Bus.
FT232 Breakout board connector.
External jumper nodes.
Board is equipped with LCD 2x16 connector
Quartz crystal 20 MHz.
ULN 2803 To drive Stepper Motor& Relays.
Reset button.
Power plug-in DC Socket.
Power supply indicator LED.
Test led for Tx, Rx.
4 digit 7Seg Multiplexed Display.
Pin outs for 12V,5V,3.3V,GND.
All IO’s are connected by brug stripps for easy connection.
High quality PCB FR4 Grade with FPT Certified.
Power supply, 5V-12V
40 pin ZIF socket for IC mount.
PICKIT3 ISP connector*.
PICKIT2 ISP connector*
Reset
4x1 7 segment display
26 pin raspberry connector
Arduino Shield footprint
ULN 2803 driver
GND Connector
Node connector
XBEE footprint/ XBEE Adaptor module
DC 3.3V connectors
DB-9 female connector
8x1 LED’s
DC 5V connectors
8 way DIP switch
RTC Module
3 Pot for Analog Variation.
EEPROM
RDL BUS.
Buzzer
4x1 keypad
16x2 LCD .
DC 5V connector
4x4 Matrix Keypad
DC 12V connectors
Power ON switch
*It require additional programmer to burn the chip through ICD ICSP socket.
